High-lifter Lift Kit for Polaris 900 XP Ranger - Signature Ser User Manual download pdf

780 Professional Dr. North, Shreveport, LA. 318-524-2270

Polaris 900 XP Ranger

Lift Kit Installation Instructions

Read Before Installation

This product is designed for use on ATVs and/or RUVs to increase ground clearance and fender clearance. It is

designed for utility type, slow-speed use on relatively flat terrain in deep mud or snow. Although we have many

thousands of satisfied lift kit customers and over 1,800 franchised dealers selling and installing lift kits, purchasers

should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise

the center of gravity on your ATV and/or RUV, increasing risk of roll-over, injury and death on all types of terrain. It

is your responsibility to always inform other operators and passengers of this vehicle about the added risks.

We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the

ATV and/or RUV. Riders should be advised that the handling characteristics of a taller ATV and/or RUV are different

and require extra care when riding, particularly on side hills or off-camber situations. If you further raise the center of

gravity by adding taller tires, heavy loads to racks or seats, or by any other means, the ATV and/or RUV must be

operated with even more care, at slower speeds and on relatively flat ground. All turns should be done at a slow speed,

even on level ground.

Operation of an ATV and/or RUV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects

the rider to the risk of serious bodily harm or possible death. This risk is compounded if the rider does not wear an

approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV

and/or RUV as a driver or passenger.

If this product is not what you expected, or is not consistent with your intended use, you should return the product

immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation,

product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the

purchase price or replacement of the kit, at the seller’s option.

Dealers and other Installers

You are responsible for informing your customer and end user of the information contained above and the increased

potential hazards of operating an ATV and/or RUV equipped with a lift kit. If you install the lift kit, it is your

responsibility to also install the warning label prominently in view of the driver and in prominent view of the driver and

passenger on RUVs and multi-passenger ATVs. They should also be instructed to notify anyone operating the vehicle,

as well as any passengers, that a lift kit is installed

As discussed above, it is critically important that they be instructed in the need for slower speed operation, regardless of

terrain, after this lift kit is installed.

NOTE: 1.5" SPACERS ARE REQUIRED IN THE REAR IF YOU ARE RUNNING FACTORY

900 RANGER STEEL WHEELS!

NOTE: IF RUNNING FACTORY RANGER 900 ALUMINUM WHEELS OR AFTERMARKET

ALUMINUM WHEELS THEN SPACERS ARE NOT REQUIRED.

1 2 3 4 5 6 7 8 9 10

Summary of Contents

Page 1 - Polaris 900 XP Ranger

1 780 Professional Dr. North, Shreveport, LA. 318-524-2270 Polaris 900 XP Ranger Lift Kit Installation Instructions Read Before Installation This

Page 2 - Parts Diagram

10 5. Fasten it tight under the frame using a ¼” washer and ¼” lock nut. 6. Once you have fasten the plate, reconnect the wires and shock to th

Page 3 - Front Lift Installation

2 Parts Diagram

Page 4

3 Front Lift Installation 1) Place UTV transmission in park. Place jack under center of UTV front end and lift until front wheels clear the ground

Page 5 - Rear Lift Installation

4 6) Now insert a spacer on each of the bolts and the other front lift bracket to the inside of the shock mount tab. Loosely fasten it with two 10m

Page 6

5 Rear Lift Installation 1) Place UTV transmission in park. Place jack under center of UTV front end and lift until rear wheels clear the ground.

Page 7

6 6) Now insert a spacer on each of the bolts and the other rear lift bracket to the inside of the shock mount tab. Loosely fasten it with two 10mm

Page 8

7 10) Remove the grease fitting from the frame and attach it to the new sway bar relocating bracket. 11) Using a 5/16 drill bit, drill a l

Page 9

8 14) Next connect the sway bar and factory sway bar bracket to the new sway bar relocation bracket. Insert the 10x85mm hex bolt through the factory

Page 10

9 High Lifter Name Plate Installation 1. Raise the dump bed on the UTV. You will need to disconnect the shock from the bed to make the installation

Comments to this Manuals

No comments

High-lifter Lift Kit for Polaris 900 XP Ranger - Signature Ser User Manual

Browse online or download User Manual for Hardware High-lifter Lift Kit for Polaris 900 XP Ranger - Signature Ser. High Lifter Lift Kit for Polaris 900 XP Ranger - Signature Series User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware High-lifter Lift Kit for Polaris 900 XP Ranger - Signature Ser